top of page
tamco.jpg
Air Foil Dampers
Series 1000
Series 1000
Tamco_Dampers_1000_1500_small.png

Series 1000 Air-Foil Control Damper:

  • Modulating, or 2 position control dampers.

  • Where maintenance is an issue.

  • Ideal and reasonably priced choice for replacing worn out common dampers.

 

ET - Elevated Temperature Option:

  • Suitable for high heat environments where temperatures may reach as high as 300°F (149°C),and where UL regulated control dampers are not a requirement.

  • For use in back-up generator stations, where excessive heat may be an issue.

  • For test laboratory applications, wherever high-heat conditions may exist.

  • A practical solution in mildly acidic applications, where Celcon bearings may not withstand environmental conditions.(See Options for more details.)

 

MR - Moisture Resistance Option:

  • Suitable for applications where dampers are exposed to extended periods of high humidity or high moisture, such as water treatment facilities, municipal pools, and greenhouses.

  • Cost effective alternative to the Salt Water Resistance Option for applications where salt spray is not a concern. (See Options for more details.)

 

SW - Salt Water Resistance Option:

  • Ideally suited for coastal climates.

  • Recommended for inland applications, where tire spray from winter-salted roads have been known to corrode dampers installed in close proximity to roads or highways.

Series 1500
Series 1500
Tamco_Dampers_1000_1500_small.png

Series 1500 Ultra-Low Leakage, Enhanced Air-Foil Control Damper:

  • When the damper is closed and a low air leakage rate is critical.

  • Where infiltration is a concern.

  • Where condensation and freeze up are not a concern, but where an energy efficient, low infiltration, maintenance-free damper is essential.

  • Ideal specification choice for outside wall dampers intended for use in warmer climates, where energy efficient, non-insulated dampers are required.

 

ET - Elevated Temperature Option:

  • Suitable for high heat environments where temperatures may reach as high as 300°F (149°C),and where UL regulated control dampers are not a requirement.

  • For use in back-up generator stations, where excessive heat may be an issue.

  • For test laboratory applications, wherever high-heat conditions may exist.

  • A practical solution in mildly acidic applications, where Celcon bearings may not withstand environmental conditions.(See Options for more details.)

 

MR - Moisture Resistance Option:

  • Suitable for applications where dampers are exposed to extended periods of high humidity or high moisture, such as water treatment facilities, municipal pools, and greenhouses.

  • Cost effective alternative to the Salt Water Resistance Option for applications where salt spray is not a concern. (See Options for more details.)

 

SW - Salt Water Resistance Option:

  • Ideally suited for coastal climates.

  • Recommended for inland applications, where tire spray from winter-salted roads have been known to corrode dampers installed in close proximity to roads or highways. (See Options for more details.)

Multi-Zone Dampers
1001MZdamper.jpg
Series 1000 MZ

  • There are no internal mechanisms that can loosen, fail, or be omitted.

  • Transmission of torque, or stroke is direct and without losses.

  • Internal zone dividers are designed to accept duct connections.

Series 1001 MZ
Series 1001 MZ
1000MZdamper (1).jpg
Series 1000 MZ
Multizone Dampers

  • Decks are connected using 7/16" (11.11 mm) extruded aluminum hex rods. The hex rods are stamped into the blade of one deck and U-bolted into the corresponding blade of the opposite deck.

  • Connections between decks will not develop any wear or play.

  • There are no internal mechanisms that can loosen, fail, or be omitted.

  • Transmission of torque, or stroke is direct and without losses.

  • Blades are specifically designed to maintain 90º operation between decks.

  • Internal zone dividers are designed to accept duct connections.

1000SMdamper.jpg
Smoke Dampers
Series 1000 SM Low Leakage
Smoke Dampers

Series 1000 SM UL/ULC Approved Two-Position Smoke Damper

  • TAMCO Series 1000 SM Two-Positon Smoke Dampers are UL/ULC approved for use in passive systems, smoke control systems, and smoke management systems.

  • These smoke dampers are designed for use in two-positon applications, where variable volume control is not required.

  • Smoke dampers are intended for installation in ducts and air transfer openings that are designed to resist the passage of air and smoke.

  • Smoke dampers may be required where ducts penetrate through smoke barriers, or at other locations within an engineered smoke control system.

  • They are installed to operate automatically, controlled by a smoke detection system, and where required, capable of being opened or closed from a remote command station.

 

MR - Moisture Resistance Option:

  • Suitable for applications where dampers are exposed to extended periods of high humidity or high moisture, such as water treatment facilities, municipal pools, and greenhouses.

  • Cost effective alternative to the Salt Water Resistance Option for applications where salt spray is not a concern. (See Options for more details.)

 

SW - Salt Water Resistance Option:

  • Ideally suited for coastal climates.

  • Recommended for inland applications, where tire spray from winter-salted roads have been known to corrode dampers installed in close proximity to roads or highways. (See Options for more details.)

Series1000 SM LL
1000SMdamper.jpg
Series 1000 SM
Series 1000 SM Low Leakage

Series 1000 SM UL/ULC Approved Smoke Damper

  • TAMCO Series 1000 SM smoke dampers are UL/ULC approved for use in passive systems, smoke control systems, and smoke management systems.

  • These smoke dampers are designed for use in modulating applications.

  • Smoke dampers are intended for installation in ducts and air transfer openings that are designed to resist the passage of air and smoke.

  • Smoke dampers may be required where ducts penetrate through smoke barriers, or at other locations within an engineered smoke control system.

  • They are installed to operate automatically, controlled by a smoke detection system, and where required, capable of being opened or closed from a remote command station.

 

MR - Moisture Resistance Option:

  • Suitable for applications where dampers are exposed to extended periods of high humidity or high moisture, such as water treatment facilities, municipal pools, and greenhouses.

  • Cost effective alternative to the Salt Water Resistance Option for applications where salt spray is not a concern. (See Options for more details.)

 

SW - Salt Water Resistance Option:

  • Ideally suited for coastal climates.

  • Recommended for inland applications, where tire spray from winter-salted roads have been known to corrode dampers installed in close proximity to roads or highways. (See Options for more details.)

Series 1000 SM -M
Series 1000SM
bottom of page